Personal Protective Equipment (PPE) Requirements: Eye and Face Protection

Personal Protective Equipment (PPE) Requirements: Eye and Face Protection

The National Institute for Occupational Safety and Health (NIOSH) reports that every day about 2,000 U.S. workers sustain job-related eye injuries that require medical treatment. However, safety experts and eye doctors believe the right eye protection can lessen the severity or even prevent 90 percent of these eye injuries.

Personal Protective Equipment (PPE) Requirements

 General personal protective equipment (PPE) requirements are addressed in 29 Code of Federal Regulations (CFR) 1910.132 :

"Protective equipment including personal protective equipment for eyes, face, head and extremities, protective clothing, respiratory devices, and protective shields and barriers shall be provided, used and maintained in a sanitary and reliable condition wherever it is necessary by reason of hazards of processes or environment, chemical hazards, radiological hazards or mechanical irritants encountered in a manner capable of causing injury or impairment in the function of any part of the body through absorption, inhalation or physical contact." (29 CFR 1910.132(a))

Eye and face protection requirements are outlined in 29 CFR 1910.133. Employers must ensure that each affected employee:

  • Uses appropriate eye or face protection when exposed to eye or face hazards from flying particles, molten metal, liquid chemicals, acids or caustic liquids, chemical gases or vapors or potentially injurious light radiation
  • Uses eye protection that provides side protection when there is a hazard from flying objects
  • Who wears prescription lenses while engaged in operations that involve eye hazards wears eye protection that incorporates the prescription in its design, or wears eye protection that can be worn over the prescription lenses without disturbing the proper position of the prescription lenses or the protective lens
  • Uses equipment with filter lenses that have a shade number appropriate for the work being performed for protection from injurious light radiation

Criteria for Protective Eye and Face Devices

More than 10 years ago (September 2009) OSHA issued a Final Rule that incorporated the latest versions of national consensus and industry standards for eye and face protective devices, head protection and foot protection. Additionally, OSHA also announced its use of "direct final rule" to ensure that when standards change, the law is automatically updated.

ANSI Z87.1

The first "standard" for head and eye protection dates to 1922 with the first edition of the Z2 standard by the War and Navy Department and the National Bureau of Standards.

In 1968, the eye and face protection standard was published with the Z87 designation, Z87.1-1968. Since then Z87.1 has been revised six times–1979, 1989, 2003, 2010,  2015 and 2020. Through these revisions, the purpose of this Standard has remained the same – to provide minimum requirements for eye and face protective devices including selection, use and maintenance of the devices.

ANSI/ISEA Z87.1-2020

The 2020 revision continues to focus on product performance and harmonization with global standards. This allows new, innovative and compliant designs to enter the market. ANSI/ISEA Z87.1-2020  now includes criteria and required markings for protectors that offer relaxed opticsfor job tasks that may not require the historically stringent optical criteria. Hazard assessments are a must to determine if relaxed optics would be suffcient.  It also now includes testing, performance and marking criteria for lenses with anti-fog properties and expanded welding filter shades.

ANSI /ISEA Z87.1-2020 sets forth numerous criteria related to the general requirements, testing, permanent markings, selection, care and use of “protectors.” A "protector” is a complete device (a product with all its components in the final use configuration) that meets the required performance criteria. Generally, the required tests must be performed on a specified number of complete devices. This number varies by testing protocol. For example, for high-mass impact four complete devices must be tested and for lateral protection one complete device must be tested. The newly added anti-fog lens treatment criteria is a lens-only assessment which is a departure from the final configuration approach. This lens-only approach is consistent with criteria in other global standards. 

All original equipment manufacturers and non-original equipment manufacturers aftermarket components not sold with the original device must be tested and assembled with the original complete device in the as-worn condition. For aftermarket sideshields, the sideshields must be tested on representative frames for which the product is specified to fit. Documentation listing all devices that the component or accessory has been tested and is approved for must be made available by the manufacturer. The entity claiming compliance of the component is responsible for testing the assembled device.

ANSI/ISEA Z87.1-2020 Markings

All compliant protections must be permanently and legibly marked as shown in the following table. Markings for lens type and use applications are only required when claims for such protection are made by the manufacturer.

Eye and Face Protector Markings

Type of Mark

Lenses and Replacement Lenses

Frame1

Marking for Complete Device2

Spectacles

All Others

Manufacturer's Mark / Logo

Yes

Yes

Yes

Yes

Standard Plano, Readers, Magnifiers

 

Z87

Z87

Z87

Standard Prescription

 

Z87

Z87-2

Z87-2

Coverage (Small Size)3

H

 

H

 

Impact Rated Plano, Readers, Magnifiers

 

Z87+

Z87+

Z87+

Impact Rated Prescription

 

Z87+

Z87-2+

Z87-2+

Relaxed Optical Level6

O2

O2

 

O2

Clear lens

       

Welding Filter Lens5

W and Shade Number (1.3 - 16)

W and Shade Number (1.3 - 16)

 

W and Shade Number (1.3 - 16)

UV Filter Lens4

U and Scale Number (2 - 6)

U and Scale Number (2 - 6)

 

U and Scale Number (2 - 6)

IR Filter Lens4

R and Scale Number (1.3 - 10)

R and Scale Number (1.3 - 10)

 

R and Scale Number (1.3 - 10)

Visible Light Filter Lens4

L and Scale Number (1.3 - 10)

L and Scale Number (1.3 - 10)

 

L and Scale Number (1.3 - 10)

Variable Tint Lens

V

V

 

V

Special Purpose Lens

S

S

 

S

Anti-Fog Lens

X

X

 

X

Splash/Droplet Use

   

D3

D3

Dust Use

   

D4

D4

Fine Dust Use

   

D5

D5

  1. Frame components subject to marking vary by type of protector. 
    • Spectacles: Frame and at least one temple. Both detachable sideshields are marked Z87+, if impact rated
    • Goggles: Frame and lens housing or carrier
    • Faceshields: Crown and chin protector
    • Welding helmets and handshields: Shell and lens housing or carrier
    • Respirators: None
    • Prescription frames: Size marking on front and temple in accordance with ANSI ISO 7998, 8624, and 12870
  2. A complete device (no replaceable components) must have at least one set of markings. The markings may be on the lens or the frames or both the lens and the frame.
  3. For spectacle protectors, coverage marking “H” must be on the lens for rimless or semi-rimless lens retention systems.
  4. In case of multiple filter type compliance, designations must be listed in the order given in the table: U, R, L.
  5. Marks for variable auto-darkening filters must include the range of dark states offered – for example “W9-12”
  6. Where a claim of compliance for both impact-rating and relaxed optical levels is made, it is acceptable, but required, for the “+” marking to be placed inside of the “O” so long as both are discernible.  No marking is required for standard optical levels.

These markings must be placed in proximity to each other in this sequence:

  • Manufacturer’s marks/logos (exempt from proximity requirement if they are clearly present elsewhere)
  • Standard designation
  • Coverage
  • Optical level
  • Optional hazard-specific marks (if applicable)
    • Impact-protector marking
    • Optical radiation marking
    • Droplet and splash marking
    • Dust marking
    • Fine dust marking
  • Optional Design marks (if applicable)
    • Anti-fog treatment

 

Commonly Asked Questions

Q: How long must lenses marked as anti-fog remain free from fogging?

A: According to the ANSI/ISEA Z87.1-2020 lenses marked as having anti-fog properties must remain free from fogging for a minimum of eight seconds. This testing applies to the lenses only and does not assess the resistance to fogging of the complete device.

Q: What should the lenses of my protective eyewear be made of?

A: Most lenses are made from polycarbonate. This lightweight plastic absorbs 99% of UV light, can be purchased in welding shades and is highly impact resistant.

Q: I need safety glasses for work, but I already wear prescription eyewear. What are my options?

A: Workers who wear prescription lenses must wear a pair of safety glasses that incorporate the prescription in its design, wear safety glasses that can be worn over prescription lenses without disturbing the proper position of either, or wear a pair of reader eyewear that would meet the user’s refractive need.

Sources

29 CFR 1910.132, General Requirements
29 CFR 1910.133, Eye and Face Protection
ANSI/ISEAZ87.1-2020, American National Standard for Occupational and Educational Eye and Face Protection Devices

The information contained in this article is intended for general information purposes only and is based on information available as of the initial date of publication. No representation is made that the information or references are complete or remain current. This article is not a substitute for review of current applicable government regulations, industry standards, or other standards specific to your business and/or activities and should not be construed as legal advice or opinion. Readers with specific questions should refer to the applicable standards or consult with an attorney.

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.